Sounds like a thermal runaway where a temperature changed too quickly and the code interpreted that as a fire or risk of fire and shut down. A lot of times that can be helped with a silicone sock and a PID tuning. Another thing is the ceramic heater core is going bad and it can’t keep a stable temp above a point. Heater cores are cheap and easy to change. The heater core is considered a consumable part and usually comes in multiple packs.

Might wanna switch that F to a C.

Hold on, the USA just fired the EPA, let’s not get any hopes up.

PETG is picky about layer heights and speed.

Thick and slow for PETG. I usually double my layer height vs what I would print in PLA. With my .6 nozzle I print with .3 layer and cut my speed down to 50% for the first layer. Since you said it happens mid print you might be printing too fast for the first few layers and it is getting too high because the layer is not cooling enough and it starts curling. You can also try reducing flow if your nozzle is worn and it’s allowing more plastic than the sclicer expects which will cause too high layers and scraping.

Oh and it sounds like it’s too hot too. 80° bed in a enclosure could cause the chamber to get too hot and not allow the layers to cool fast enough and so you will see curling while printing. Lower the bed to 40-50 and monitor chamber temps. Maybe open the doors a crack. You only need an enclosure for PETG if the room is drafty.

Been using it for awhile now. Do we have a way to use our phones as the play yet? I want to be able to listen on my phone with headphones or even in my car with Android Auto. I would love to be able to delete my Spotify app. I still use the service because the radio feature is still much better than MA. But once I can do everything that Spotify can be I can cancel my Spotify account.

Doritos™ presents, I don’t normally read long posts but I was hooked from the start.

A good way is to impose a massive state tax on the rich. They can run to other states but if they want to operate their businesses in the state they will have to pay.

Well maybe states will have to secede from the USA. If federal funding is cut then there is no reason to be part of the federal government. Texas has been threatening to leave for so long and that allows them to throw a tantrum and get their way. Maybe other states need to follow their lead and make the threat.

That is a bed leveling issue. It’s too far away where there are gaps and too close where there is rippling. Run a bed leveling procedure and if the model allows for manual leveling you should go through that and then do another mesh leveling.

Also clean your build plate with soap and water and avoid touching it with bare hands.

So online farmers/flea market?

Annnnnd they are fired again… just kidding hopefully.

6 Planeteers? What power does #6 have? 5th element?

I started with a cheap kit from a company that no longer exists. Over the last 15 years I have added and upgraded parts. I would say buy what you can afford and then upgrade as you go. The uv and remineralizers are nice to have but not needed. Just be sure to get a 5 stage to start. 3 stage pre filters plus membrane and charcoal. Another good upgrade is a permeate pump, it boosts the efficiency and saves water on the waste. I have my waste water fed out to water my garden in the summer.

I once even tried to add a Deionization filter before the minerals that way it was almost 0ppm tds before adding back the minerals but it seemed to destroy my mineral cart and made my water smell fishy.

I am not an expert just a homeowner with 15 years of filtering my own water.

Which is strange because you would think keeping the price low enough to sway customers away from other services or low enough it’s forgettable (gym membership style) or just low enough to keep people from canceling would net them more customers and make up for the lower rates.

But no they keep increasing and driving more people away which in turn causes them to raise rates again this is a death spiral.

Mice are not human, drug prob won’t work the same way in humans. IANAS

Gotta go fat

More drives mean more heat and more power usage. Better to have two large with parity enabled. The chances of both failing is very rare. Should be using an online backup service like backblaze or having a plan to take a copy off-site.

What? How did you think I said that? My comment was a positive. Summer of love was awesome.

That will spark the summer of love 2.0. Might see an uptick in other STDs though